spd components

Product Features ● Sus 304 stainless steel housing. ● Protection Level IP67. ● Standard threaded interface mounting. ● Series connection, low residual voltage. ● Suitable for installation in LPZ2-3 and subsequent lightning protection zones, as lightning protectors for communication signal line equipment in intrinsically safe areas of natural gas, gas stations, petroleum, and petrochemical systems, such as sensors and transmitters. Applications Suitable for installation in

LTS-40A/LTS-63A Decoupling Coil Crafted with high-quality copper wire winding and a broadband magnetic core, this decoupling device is engineered for scenarios where the cable decoupling distance between two levels of surge protection devices (SPDs, e.g., T1-T2, T2-T3, T2-T1) is insufficient. It acts as a key component in energy coordination between SPDs, preventing subsequent SPDs from damage caused by lightning current and reducing residual voltage. Product features ●Made

LTS-40A/LTS-63A Decoupling Coil Crafted with high-purity oxygen-free copper wire winding and a broadband magnetic core, this decoupling device is purpose-built for scenarios where the cable decoupling distance between two tiers of surge protection devices (SPDs, e.g., T1-T2, T2-T3, T2-T1) is inadequate. It serves as a critical component in energy coordination between SPDs, safeguarding downstream SPDs from lightning-induced current damage and minimizing residual voltage

Product Features ● One port, full mode protection ● Small size and easy installation ● Protection level up to IP67 ● Suitable for installation in LPZ 2-3 and subsequent lightning protection zones, parallel installation in the front end of the final level equipment of the AC/DC power supply system, widely used as lightning protectors for LED street lights, sensors, and other equipment Product Specification Standards IEC 61643-11 SPD type T2,T3 Models LPF 5-320 LPF-10-320

About this item 1.Ultimate Protection: Our surge protector is designed to shield electrical systems and load devices from the damaging effects of lightning strikes and sudden voltage surges. 2.High-Performance: Equipped with copper components for superior conductivity and precision. It reacts swiftly during lightning strikes to relieve pressure, safeguarding your electrical systems and devices from transient over-voltages. Compatible with various photovoltaic systems. 3

Product features ● Full mode protection ● No leakage current, no afterflow ● Large flow capacity and super low residual pressure ● Suitable for installation in LPZ 1-2 and subsequent lightning protection zones, suitable for fine lightning protection devices in three-phase power supply systems. Product Specification Standards IEC 61643.11 SPD type T2,T3 Models SLV-40T SLV-80T Nominal operating voltage Un 220Vac(50Hz) Maximum continuous operating voltage Uc 320Vac(50Hz) Nominal

SLV-10S/SLV-20S is a compact ultra-low residual voltage surge protection device designed for single-phase power supply systems, ideal for fine lightning protection in LPZ 1-2 and subsequent lightning protection zones. As a series-installed fine arrester at the front end of equipment, it integrates full-mode protection to shield against surges in line-neutral, line-earth, and neutral-earth paths.Equipped with LED status indication (green: normal; red: failed) and open-circuit

Product Description Laboratory precision measuring instruments are highly sensitive to voltage fluctuations and lightning surges; transient high voltage causes sensor calibration drift and permanent circuit damage. This 4-pole Type 2 SPD is installed on lab three-phase incoming distribution panels. The low voltage variant delivers residual voltage as low as ≤ 1.25kV with ≤ 25ns nanosecond-level response to divert surge currents and contain impulse voltage within instrument

Dual-function combined SPD integrating Type 2 high-current diversion and Type 3 precise voltage clamping, installed at LPZ1-LPZ2 terminal zones and coordinated with front Type 1 arresters for staged surge suppression. 25ns nanosecond phase response instantly blocks grid switching voltage spikes, two Uc variants match regional impulse withstand requirements. Vibration-resistant modular build reduces loose contact risks on production lines, standardized 5N·m torque enables