spd components
"
Explosion Proof SPD Components 24Vdc 250mA IP67 10kV For Intrinsically Safe Area
Product Features Sus 304 stainless steel housing. Protection Level IP67. Standard threaded interface mounting. Series connection, low residual voltage. Suitable for installation in LPZ2-3 and subsequent lightning protection zones, as lightning protectors for communication signal line equipment in intrinsically safe areas of natural gas, gas stations, petroleum, and petrochemical systems, such as sensors and transmitters. Applications Suitable for installation in
Outdoor Industrial Lighting Protection LED Spd Surge Protection Device 220V 5kA 10kA IP67
Product Features One port, full mode protection Small size and easy installation Protection level up to IP67 Suitable for installation in LPZ 2-3 and subsequent lightning protection zones, parallel installation in the front end of the final level equipment of the AC/DC power supply system, widely used as lightning protectors for LED street lights, sensors, and other equipment Product Specification Standards IEC 61643-11 SPD type T2,T3 Models LPF 5-320 LPF-10-320
Whole House SPD Decoupler 40A 15μH DIN Rail T1 T2 Coordination Industrial Protection
LTS-40A/LTS-63A Decoupling Coil Crafted with high-quality copper wire winding and a broadband magnetic core, this decoupling device is engineered for scenarios where the cable decoupling distance between two levels of surge protection devices (SPDs, e.g., T1-T2, T2-T3, T2-T1) is insufficient. It acts as a key component in energy coordination between SPDs, preventing subsequent SPDs from damage caused by lightning current and reducing residual voltage. Product features Made
Industrial Whole House Surge Protector Decoupler 40A 15μH DIN Rail SPD T1 T2
LTS-40A/LTS-63A Decoupling Coil Crafted with high-purity oxygen-free copper wire winding and a broadband magnetic core, this decoupling device is purpose-built for scenarios where the cable decoupling distance between two tiers of surge protection devices (SPDs, e.g., T1-T2, T2-T3, T2-T1) is inadequate. It serves as a critical component in energy coordination between SPDs, safeguarding downstream SPDs from lightning-induced current damage and minimizing residual voltage
T2 T3 Lightning Surge Protection Device 3 Phase AC SPD 220V 20kA 40kA
Product features Full mode protection No leakage current, no afterflow Large flow capacity and super low residual pressure Suitable for installation in LPZ 1-2 and subsequent lightning protection zones, suitable for fine lightning protection devices in three-phase power supply systems. Product Specification Standards IEC 61643.11 SPD type T2,T3 Models SLV-40T SLV-80T Nominal operating voltage Un 220Vac(50Hz) Maximum continuous operating voltage Uc 320Vac(50Hz) Nominal
Low Voltage Surge Protection Device Spd DIN Rail Mount Surge Suppression Device 220V 10kA 25kA
SLV-10S/SLV-20S is a compact ultra-low residual voltage surge protection device designed for single-phase power supply systems, ideal for fine lightning protection in LPZ 1-2 and subsequent lightning protection zones. As a series-installed fine arrester at the front end of equipment, it integrates full-mode protection to shield against surges in line-neutral, line-earth, and neutral-earth paths.Equipped with LED status indication (green: normal; red: failed) and open-circuit
Lightning Protection T1 T2 SPD 3 Phase Home Surge Protector 220V 25kA 40kA 80kA
LPM 25B-385/4/LPM 50B-385/4 is a T1+T2 level power surge protector. It integrates primary (T1) and secondary (T2) protection, providing comprehensive shielding against direct and indirect lightning strikes. Product features Integrated module design:Integrated module design enables hot-swappable replacement, accurate surge protection, and cost-effective maintenance. Support Kevin Connection:Featuring an integrated module design, ensuring accurate current measurement and
